Publications
2002
A. Podgornik, M. Barut, S. Jakša, J. Jančar, A. Štrancar
Journal of Liquid Chromatography & Related Technologies Vol. 25, No. 20, pp. 3097–3114, 2002
Convective Interaction Media® (CIM) disk monolithic columns are specific among the chromatographic columns because of their monolithic structure and extremely short column length. In this work, HETP values and Z factors for different groups of molecules—proteins, DNA, oligonucleotides, peptides, and organic acids on strong anion exchange CIM disk monolithic columns were determined. Results are discussed in terms of the molecule structures and applied to develop different approaches for successful separation of abovementioned group of molecules on these types of columns.
R. Hahn, M. Panzer, E. Hansen, J. Mollerup, A. Jungbauer
Separation Science and Technology, 37(7), 1545–1565 (2002)
The mass transfer properties of polyglycidylmethacrylate–ethylenedimethacrylate monolithic ion-exchangers (convective interaction media disks) were evaluated. As a reference material, the particulate ion-exchanger Source 30 was selected. The model proteins lysozyme, bovine serum albumin, and IgG were loaded at different concentrations and velocities. The mass transfer zones obtained with the monoliths were affected by neither the linear flow velocity nor the protein concentration in the mobile phase. The reduced height equivalent to one theoretical plate (HETP) of monoliths were independent of the reduced velocity. This was not the case for the particulate material.
A. Štrancar, A. Podgornik, M. Barut, D. Glover
BIOforum International 3/2002
In adsorptive chromatographic modes, the slope of the capacity factor k' (defined as the molar ratio of the separated compound in the stationary phase and the mobile phase) plot versus composition of the mobile phase is very steep. Up to a certain composition of the mobile phase, k' is so high that the protein is bound to the stationary phase and does not move along the column. Reaching a defined point, a small change of the mobile phase composition causes a rapid decrease in k' to a value near zero. At this point, the protein dissolves in the mobile phase and passes through the column practically without any retention. In other words, the protein remains adsorbed at the top of the column until the eluting power of the mobile phase reaches the point at which a small change in the composition of the mobile phase causes the movement of the protein without any retention. One can also speak about selective elution of the compound. As a result of this process, even very short columns can provide very good separations and recovery, while longer columns might cause problems due to unspecific binding, product degradation and minor changes in the structure of the protein which increase with the length of the column. On the other hand, short-beds are very difficult to pack with particles and form channels which eliminate the resolution power of the column. Monolithic supports offer an ideal solution to avoid most of these problems.
K. Pflegerl, A. Podgornik, E. Berger, A. Jungbauer
Biotechnology and Bioengineering 79 (2002) 733-740
Screening of peptide ligands for affinity chromatography usually involves incubation with the target protein in a batch system. In an additional step, peptides with fast binding kinetics have to be selected in respect to satisfactory performance under flow conditions on a support ensuring optimal three-dimensional presentation of the peptide. We have developed a rapid screening system based on peptide synthesis and screening on CIM® disks. The disk size was minimized to fit into microplates usually applied for solid-phase extraction. In combination with a vacuum manifold, semi-automated peptide synthesis and screening for binding to a target protein under simulated chromatography conditions are possible. Various analytical methods can be applied for parallel and automated determination of the quantity, integrity, or activity of the target protein in the flow through or bound to the affinity support. This system also allows parallel screening for suitable chromatographic conditions like running buffer, washing, and elution conditions. © 2002 Wiley Periodicals, Inc. Biotechnol Bioeng 79: 733–740, 2002.
T. Tennikova, A. Štrancar
LabPlus international February - March 2002, Volume 16
Monolithic supports are a novel generation of stationary phases that can be used for liquid and gas chromatography, capillary electrochromatography, bioconversions, as well as supports for solid phase synthesis. In contrast to individual particles packed into chromatographic columns, monolithic supports are cast as continuous homogeneous phases. They provide high rates of mass transfer at lower pressure drops and enable much faster separations. In addition to the speed, the nature of the pores allows easy permeability for large molecules. Monolithic supports are thus the method of choice for the separation of proteins, oligonucleotides, and nanoparticles such as pDNA and viruses. In this article we review the application of the monlithic columns to bioaffinity chromatography.
K. Pflegerl, A. Podgornik, E. Berger, A. Jungbauer
Biotechnology and Bioengineering 79 (2002) 733-740
Screening of peptide ligands for affinity chromatography usually involves incubation with the target protein in a batch system. In an additional step, peptides with fast binding kinetics have to be selected in respect to satisfactory performance under flow conditions on a support ensuring optimal three-dimensional presentation of the peptide. We have developed a rapid screening system based on peptide synthesis and screening on CIM® disks. The disk size was minimized to fit into microplates usually applied for solid-phase extraction. In combination with a vacuum manifold, semi-automated peptide synthesis and screening for binding to a target protein under simulated chromatography conditions are possible. Various analytical methods can be applied for parallel and automated determination of the quantity, integrity, or activity of the target protein in the flow through or bound to the affinity support. This system also allows parallel screening for suitable chromatographic conditions like running buffer, washing, and elution conditions.
2001
I. Mihelič, M. Krajnc, T. Koloini, A. Podgornik
Ind. Eng. Chem. Res. 2001, 40, 3495-3501
Monolithic stationary phases are becoming more and more important in the field of liquid chromatography, because they enable extremely fast separations. Methacrylate-based monoliths are produced via a free-radical bulk polymerization of glycidyl methacrylate and ethylene dimethacrylate using a benzoyl peroxide as an initiator. Preparation of large monoliths represents a big problem because of the heat release during the polymerization, which consequently leads to the distortion of the structure. A closer investigation of the polymerization, using differential scanning calorimetry, was performed in order to determine global kinetic parameters. A multiple heating rate method, based on the work of Ozawa, Flynn, and Wall, was applied for estimation of the values of the apparent activation energy, preexponential factor, and reaction order. Global polymerization kinetics is of first order with A = 1.681 × 109 s-1 and Ea,app = 81.5 kJ/mol, where the heat of polymerization is approximately 190 J/g. In addition, the influence of air and nitrogen atmosphere on polymerization is presented.
M. Merhar, A. Podgornik, M. Barut, S. Jakša, M. Zigon, A. Štrancar
J. Liq. Chrom. & Rel. Technol., 24(16), 2429-2443 (2001)
Monoliths have already proven to be efficient chromatographic supports for the separation of various types of molecules. In this paper, the characterization of the novel reversed-phase support, CIM® RP-SDVB disk monolithic column is presented.
Using a 3 mm long RP-SDVB disk monolithic column, excellent separation of proteins within a very short time was achieved. The pressure drop observed on the column was considerably low (few bars), even at flow rates of the mobile phase up to 30 mL/min. Due to the low pressure drop, the use of high flow rates was preferred since they did not influence the quality of the gradient separation. The separation of test proteins was performed within only 14 seconds; faster separations were limited by the configuration of the HPLC system.
Furthermore, RP-SDVB disk monolithic columns were applied for fast separation of peptides. Five peptides of different lengths and composition were successfully separated in a very short time.
Finally, the preparative purification on the laboratory scale of the complex sample of oligodeoxynucleotide within a range of 1 minute demonstrates practical applicability of these columns.
I. Mihelič, T. Koloini, A. Podgornik, M. Barut, A. Štrancar
Acta Chim. Slov. 2001, 48, 551-564
Monolithic stationary phases are becoming very important field of liquid chromatography. Methacrylate based CIM Convective Interaction Media® monolithic columns and are produced via radical polymerization, which results in a rigid and chemically very stable porous monolithic structure. Some characteristics of small-scale monolithic columns and an example of extremely fast separation of biomolecules are presented in the paper. However, the preparation of large and homogeneous monolithic columns represents a big problem, because the heat released during the polymerization causes distortion of the monolithic structure. A mathematical model employing the polymerization kinetics for the prediction of the temperature profiles and a comparison with the experimental results is presented with the emphasis on the conversion and the rate od the heat release profiles. Finally, the characteristics of a large-scale monolithic column are presented.
2000
R. Hahn, A. Jungbauer
Analytical Chemistry, 7.2. 2000, (4853-4858)
Monoliths are stationary phases cast as a continuous medium which are interlaced by flow channels ramified with micropores. Pulse response experiments with bovine serum albumin as a model protein were applied for testing polymethacrylate-based monoliths, resulting in peak broadening that practically was not influenced by the chromatographic velocity. An empirical model was developed to describe peak broadening, allowing a term to account for the pore convection and a term for the pore diffusion. A diffusional distance lower than 10 nm was estimated. This corresponds to values observed with monodisperse 1-μm particles. Systematic investigations by changing the response time of the detector showed that the full potential of the monoliths could not be exploited, since the currently available chromatography systems are the limiting factor regarding the speed of data acquisition and virtual peak broadening by the infinite length of the detector. Inertia of the liquid and synchronization between liquid handling and electronic control introduced an additional disturbance. At the lowest possible response time, reliable peak data could be obtained up to a velocity of 35 cm/min. The pressure drop along the continuous bed was much smaller compared to a conventionally packed bed. Different flow patterns and significantly reduced eddy vortexes may be responsible for the high specific permeability.
H. LeThanh, B. Lendl
Analytica Chimica Acta 422 (2000) 63–69
A fully automated method for the rapid determination of organic acids (citric-, malic- and tartaric acid) and sugars (glucose, fructose, and sucrose) in soft drinks by sequential injection Fourier transform infrared (FTIR) spectroscopy is presented. A convective interaction media (CIM) disc carrying quaternary amino moieties was added as a solid phase extraction column to the flow system. Upon injection of a sample the organic acids were completely retained on the CIM disc whereas sugars passed to the flow cell. The organic acids were subsequently eluted by injection of an alkaline (pH 8.5) 1 M sodium chloride solution and recorded in their fully deprotonated form as a second flow injection peak. In both cases, the FTIR spectra corresponding to the peak maxima were selected for data evaluation. Two partial least squares models, one for sugars and the other for organic acids, were constructed based on the analysis of standards containing all six analytes. The developed method was applied to natural samples yielding results which were in good agreement with those obtained by an external reference method (enzymatic test kits). Deviations in the results were 3.4. and 4.1% for citric and malic acid and ranged from 4.7–5.1% for the sugars. The developed method is characterized by its short analysis time, experimental simplicity and its potential applications in routine analysis and process control.
1999
A. Podgornik, M. Barut, J. Jančar, A. Štrancar, T. Tennikova
Analytical Chemistry, 1999, Vol. 71, No. 15, 2986-2991
High-performance membrane chromatography (HPMC) proved to be a very efficient method for fast protein separations. Recently, it was shown to be applicable also for the isocratic chromatography of plasmid DNA conformations. However, no study about the separation of small molecules has been performed until now. In this work, we investigated the possibility of gradient and isocratic HPMC of small molecules with Convective Interaction Media disks of different chemistries and tried to explain the mechanism that enables their separation. We demonstrated that it is possible to achieve efficient separations of oligonucleotides and peptides in the ion-exchange mode as well as the separation of small hydrophobic molecules in the reversed-phase mode. It was shown that similar peak resolution can be provided in both gradient and isocratic modes.
A. Podgornik, M. Barut, J. Jančar, A. Štrancar
Journal of Chromatography A, 848 (1999) 51–60
In this work, the isocratic separation of oligonucleotides in the ion-exchange mode on thin glycidylmethacrylate–ethylenedimethacrylate (GMA–EDMA) monoliths in the form of commercially available CIM (Convective Interaction Media) disks is presented. It was found that isocratic separation occurs even on monoliths with a thickness of only 0.75 mm. Peak broadening of the components retained on the monolith is proportional to the retention time, which in turn is proportional to the thickness of the monolith. Peak height is inversely proportional to the retention time. From these results it can be concluded that the mechanism of the separation on such monoliths is similar to that in HPLC columns filled with conventional porous particles. The height equivalent to a theoretical plate of GMA–EDMA monoliths is calculated to be 18.0 μm. The capacity factor k′ depends, exponentially, on the salt concentration. The Z factor calculated from fitted equations increases linearly with the oligonucleotide’s length. It was also found that the difference between peak retention volume slightly increases with the flow-rate when the experiments are performed in the range from 0.5 to 7 ml/min. From the similarities between the isocratic separations on conventional columns and on thin GMA–EDMA monoliths it is reasonable to believe that separation based on a multiple adsorption/desorption process also occurs in thin monoliths.
D. Josić, A. Štrancar
Ind. Eng. Chem. Res. 1999, 38, 333-342
For fast separation of biopolymers, recently developed media have become increasingly widespread. They consist either of membranes or of compact, porous disks and tubes, both called Convective Interaction Media (CIM). Separation can be carried out in every mode, e.g., ion-exchange, reversed-phase, hydrophobic-interaction, and affinity recognition. The units can be used for analytical as well as for preparative purposes. Such fast analytical units will allow separations within less than 10 s and can therefore be used for in-process analysis. The advantages and disadvantages of such analytical and preparative separations are discussed along with technical problems which have been solved.
1998
M. B. Tennikov, N. V. Gazdina, T. B. Tennikova, F. Švec
Journal of Chromatography A, 798 (1998) 55–64
The effect of porous structures of 2-mm thick diethylamine functionalized monolithic polymethacrylate discs on their chromatographic behavior in ion-exchange mode has been studied. Discs with small pores did not perform well because they exhibited high back pressure and substantial peak broadening. Discs characterized with pores larger than 1 000 nm did not provide good separations either because the time required for some protein molecules to traverse the length across the pore to reach the wall for adsorption/desorption process that is essential for the separation may be longer than their residence time within the matrix. Optimum pore size is centered at about 700 nm. Excellent separations have been achieved with these discs even at very steep gradients and high flow-rates which allow to shorten the separation times substantially.
A. Štrancar, M. Barut, A. Podgornik, P. Koselj, D. Josić, A. Buchacher
LC-GC International – October 1998, 660-670
Separation supports based on convective interaction media (CIM) allow higher throughputs and separations; faster by one order of magnitude when compared with separation materials based on conventional porous particles (1). In the future, they may well play an important role in the production and quality control of diagnostic and therapeutic products based on large biomolecules. A major advantage of CIM is their use in control procedures during production processes — an important factor in satisfying the demands of regulatory authorities, both with regard to the registration of the product as a drug, and also in controlling the process in such a manner that immediate correction is possible should the process deviate from the prescribed path. The CIM supports can easily be scaled up because the larger units are made of the same material and can be used for fast separations on the preparative level. Additionally, these supports can be used for the ‘so-called’ conjoint liquid chromatography (CLC), by combining two or more discs with different ligand groups in the same housing. Finally, owing to their low back pressures and very fast response, CIM supports can be used as biosensors or bioreactors with immobilized enzymes.
1996
A. Štrancar, P. Koselj, H. Schwinn, D. Josić
Analytical Chemistry, Vol. 68, No. 19, October 1, 1996
Production and downstream processing in biotechnology requires fast and accurate control of each step in the process. Improved techniques which can be validated are required in order to meet these demands. For these purposes, chromatographic units containing compact porous disks for fast separation of biopolymers were developed and investigated with regard to their performance and speed. The problems that have, in the past, arisen from the use of wide and flat separation units, such as membranes and disks, have chiefly been those of sample distribution and large void volumes before and behind the unit. Improvements in the construction of the cartridge have led to better performance of the compact porous disks and faster separation. Using these disks, three calibration standard proteins could be separated within less than 1 min by an anion-exchange, cation-exchange, and hydrophobic interaction mode. Such units can be used for in-process control in production and downstream processing of biopolymers, as was shown in experiments involving the purification of α1-antitrypsin and clotting factor IX and the immobilization of enzyme glucose oxidase on an epoxy-activated compact porous disk.
1995
B. G. Belenkii, V. G. Malt'sev
BioFeature, BioTechniques, 288, Vol. 18, No. 2 (1995)
In gradient chromatography for proteins migrating along the chromatographic column, the critical distance X0 has been shown to exist at which the separation of zones is at a maximum and band spreading is at a minimum. With steep gradients and small elution velocity, the column length may be reduced to the level of membrane thickness-about one millimeter. The peculiarities of this novel separation method for proteins, high-performance membrane chromatography (HPMC), are discussed and stepwise elution is shown to be especially effective. HPMC combines the advantages of membrane technology and high-performance liquid chromatography, and avoids their drawbacks.
1990
T. B. Tennikova, B. G. Belenkii, F. Švec
Journal of Liquid Chromatography, 13(1), 63-70 (1990)
Basing on the fact that only short layers of a chromatographic column contribute to the separation in the interaction chromatography, 1 mm thick membranes from macroporous methacrylate polymer provided with functional groups were synthetized and used for protein separation. The chromatograms show that the separation is fully comparable with that experienced on a filled column but the advantage of a membrane is up to two orders of magnitude lower pressure during the process and very high loading reaching up to 40 g/m2. This recommends the high performance membrane chromatography also for large scale preparative separations.